Dr.Vilas Deshmukh

Dr.Vilas Deshmukh

Friday, January 25, 2013

Affordable Technology for Rural concrete roads


Affordable Technology for Rural concrete roads   

Dr.V.V.Deshmukh
(A white paper on affordable technology for rural concrete roads
Rural roads mostly bituminous roads are in bad shape because of severe climatic conditions in our country. Funds for maintenance are not available resulting very bad condition of road in our country. The concrete roads are recommended for our country because no severe climatic condition affect the performance of concrete roads.

The main constrain is the cost .There is general perception of the construction fraternity the concrete is very costly. The old pundits of the pavement industry are familiar with asphalt pavement because last five decades the asphalt roads are made over concrete. People are not aware of significant development in concrete admixture. and its effect on strength and performance. It is possible to produce concrete at much cheaper rate

According to Mr.P.Bongirwar out of 33lack km of length only 2lakh kilometre carry heavy traffic from 30MSA to 200 MSA and only about  50000 kilometre may be carrying more than 100 MSA. Majority of village roads and ODR of about 28 lack kilometre must be carrying traffic less then 3MSA.Considering the  present road construction activity the same will need 175 cubic meter of aggregate every year which is creating environmental issue .Large requiring of sand also creating problem of underground water. Heavy consumption of diesel and bitumen is increasing our burden of foreign exchange .Most of the village roads are seriously affected due to inadequate provision of maintenance grands.
omt 90% length is metalled and top WBM layer is seriously affected and not in traffic worthy condition .The black topped village roads are also heavily damaged due to lack of renewal coat. Huge funding is required to revive these assets to proper standards .we therefore plan such specifications and develop technology which can result into more durable assets at minimum affordable cost. All low volume road is usually provided with thin bituminous surfacing which require constant maintenance of potholes formed during rains. The road also require major renewals such as bituminous carpet and seal coat after every five years. if there is water logging due to lack of drainage the bituminous surface may get damp within a week of construction and entire investment is lost in a short time There is need for suitable pavement material having expected life of 15 to 20 years which is low in initial and maintenance cost not affected by water labour intensive and employment generation and dust free environment.

The author has categorised the village roads as roads villages turning cities and village roads.

The city roads The traffic of the city road is of cars ,rickshaws, buses, trucks  etc. The axle load is of 10MSA.The thickness of the road is 100mm based on IRC -78. The optimum mix design is given below. 
Historical development in urban pavement technology at TMC


MIX DESIGN FOR WHITE TOPPING AS OVERLAY
 for TMC CORPORATION
MATERIAL
kg/M3
RS/KG
COST
DENSITY
VOLUME
cement
360
6.00
2160
3.15
114.29
flyash
150
2
300
2.25
66.67
micro silica
0
22
0


sand
917
0.6
550.2
2.69
340.89
metal-2
450
0.6
270
2.88
156.25
metal-1
550
0.6
330
2.88
190.97
admix
3
140
420
1.23
2.44
water
160
0.4
64
1
160.00
fiber
0
225
0

1031.51

2590

4094.2



COMPRESSIVE STRENGTH
7-DAYS
25mpa
28-days
40mpa
510.00
water/powder
0.88
88
past content
0.33
36
sand content
0.33048015
35
coarse aggregate
0.33661683
28
.THIN WHITE TOPPING IS GRDUALLY BECOMING POPULAR IN URBAN AREAS The author has developed the above mix design and first time laid 100meter stretch of white topping in thane city in the year 2008.The project was successful and 25 kilometre white topping is done in thane city .The methodology is given below. The life cycle study certainly prove that white topping is cheaper than conventional bituminous roads



FIG1 Milling of existing bituminous road
FIG2 Sub base preparation
Fig3 concrete laying
FIG4 UTWT Topping
Historical development in rural pavement technology at Murbad Thane
The Thane unit of PMGSY made history by adopting /experimenting technology which is different than regular prescribed method of Road building
In the month of April 2011 thane unit of PMGSY  was successful in laying 150 mm of PQC on 150mm of GSB The concrete used was totally different than conventional concrete.
1.      The M-40 Grade concrete is made by using 290kg of cement. The reduction in cement quantity was possible by using additives like flyash,silica fume,GGBS etc. and by using water reducing admixture  like BASF Glenium sky, Glenium 276 etc.
2.      The SCC technology is used to achieve concrete to spread of its own weight.
3.      First time the joint cutting is avoided by placing geopolymer strips of 50mm in 150mm concrete at regular interval.
Three fundamental changes in concrete technology made it possible to give concrete roads to villages  in slightly higher cost.

The white topping has made distinct difference in the output.
1 Maintenance free roads for next fifteen years
2  Acceleration of rural economy.
3 Saving in raw material namely lime stone by less use of cement .
Few photographs of concrete road at kunde bangar wadi under the scheme of prime minister of gram Sadak yogna
Mix design for PMGSY
SCC concrete
MATERIAL
kg/M3
RS/KG
COST
DENSITY
VOLUME
cement
290
5.40
1566
3.1
93.55
flyash
200
1.8
360
2.25
88.89
sand
355
0.6
213
2.69
131.97
crush stone
355
0.75
266.25
2.88
123.26
metal-2
536
0.6
321.6
2.88
186.11
metal-1
630
0.6
378
2.88
218.75
admix-BASF-B-276
3
140
420
1.23
2.44
water
150
0.4
60
1
150.00





994.97

2519

3584.85



slump flow
400mm
ycone
8sec
water/cementitious
0.306122

Gradation for crush stone and sand
%PASSING
10MM
100
4.75MM
90-100
2.36MM
60-95
1.18MM
30-70
600MICRON
15-34
300MICRON
5_20
150MICRON
0-10

Gradation for metal i&ii
Gradation for metal i&ii
metal ii
metali
%passing
20mm
95-100
100
16mm
12.5mm
90-100
10mm
25-55
40-85
4.75mm
0-10
0-10
Flyash should be from field 3 residue on 45 micron is 10%

A trail stretch of about 900m with above technology has been done for a project near kalyan Feasibility and cost advantage has been proved beyond doubt.
Historical work carried out in Bhangarwadi village near kalyan.is given below


            FIG1 Mixer for making concrete,FIG2 Laying of channelFIG3 Placing of concreteFIG4Authorities inspecting the roadFIG5Ready to use road

For village roads normally crust consist of 300mm sub grade ,200mm GSB,150-
to 225 mm WMM  20MM carpet and seal coat. Carpet and seal coat does not add to strength. but act as dust proof course .it also prevents the sucking of blindage from WMM due to pneumatic tyre and thereby prevents the damage to WMM/WBM surface. Most of the village roads are metal led and for the want of maintenance grand top later is worn out. Almost top  75mm to 100mm WBM/WMM Layer is heavily damaged in such cases normally additional 75mm to  100mm WBM/WMM layer is added and road is restored to proper cmber.20mm carpet and seal coat is added as wearing course
As an alternate to above the levelling course itself could be converted in to white topping layer the structure could be on line of white topping technology.
The WBM of hand broken material/crushed aggregates of proper gradation are laid it will  then be rolled and compactedThe entire surface then will be grouted with specially designed flow table grout and compacted again.

Rate analysis  of technology similar to coalcrete
length
1000
m
breadth
3
m
thick
0.05
m

volume m3
150
voids%
30
total voids m3
45
grout quality
%
m3
kg
ton
cost/ton
cost in Rs
cement
20
8.955224
19701.49
19.70149
5600
110328.4
aggrgate
70
31.34328
68955.22
68.95522
700
48268.66
flyash
10
4.477612
9850.746
9.850746
1800
17731.34
admix
0.5
0.223881
1100
1.1
150000
165000
sf
0
0
0
0
28000
0



total
341328.4

grout density
2200kg/m3
cost in Rs
aggregate in tons
211.5
211500

aggregate cost
211500
211500

552828.4
box making with geopolymer
50000
labour and machinery
110565.7
tax
27641.42
profit 20%
110565.7


851601.1
m3
5677.341
sq.meter
283.867

 FIG1Mixing of fine powder materials,FIG2 Spreading of hand broken stones across the damaged road,FIG3 Grout prererationFIG4 Pouring the groutFIG5Final road
 The cementitious grouts

The high quality cheaper grouts are prepared. In order to keep the cost of the grout competitive additives like flyash, GGBS are used in large proportion. In order to keep the grout in suspension polymer based admixture is used..the pore volume is adjusted using lower size stone.
Few compositions of high strength cementitious grouts are given below

Compressive strength test results of grouts with Tata flyash
CEMENT
55
55
45
45

TFA
40
45
55
50

SF
5
5

ADDITIVE
0.5
0.5
0.5
0.5

WATER
20.6
20.3
18.3
18.6


STRENGTH Kg/Cm2)


1-Day
244
208
102
165

3-Day
728
755
599
543

7-Day
753
879
760
672

28-Days
Results awaited


The grout using TATA flyash can achieve compressive strength of 100Mpa.
Comparison of modified grouts compositions with normal grout using SF
composition
Gr-II
50cement
35cement
30cement
45cement
50pozo
65pozo
70pozo
30pozo
30Dahanu
comp.strength
1-Day
199
293
189
133
134
3-Days
433
436
300
248
316
7-Days
528
526
450
430
480
28-Days
633
Pozocrete micronized flyash can replace costly silicafume
Trials conducted using slag cement
Slag cement
55
60
65
flyash
40
35
30
SF
5
5
5
Additive
0.5
0.5
0.5
water
27
26
25
Compressive strength(kg/cm2)

1-Day
54
85
114

3-Days
185
233
321

7-Days
275
330
522

28-Days
530
650
710

Preparation of base for roads;

The damaged bituminous roads are cleaned and milled using milling machine. The 50mm thick of 30mm stone are laid on the damaged bituminous roads. rolled with vibratory roller and the high strength grout is poured in to the pores of the aggregate bed.
The 30mm aggregates are even prepared from the rock at site by hand braking.This will provide employment to rural youth.
The high quality cheaper grouts are poured into the 30mm stone laid on the damaged roads. rolled with vibratory roller and the grout is penetrated into the pores of the bed
The compressive and flexural strength of such roads tested inlab is found to be 40Mpa and 4.25Mpa respectively
It is observed that during the testing of compressive strength at some occassion the aggregates were fractured keeping the matrix strong.
Cost of the grout is Rs 4/kg which can be further reduced by at least one rupee by having dialog with admixture manufacturers.
The grout composition
material
Gr-1
Gr-2
cement
55
45
flyash
45
55
admixture
0.5
0.5
water
30
30

The cost of square meter road.
The cost of the road is approximately Rupees 350  per meter square.
The technology is rural friendly it requires only blender for grout preparation and pump to deliver the grout at site. Unskilled labour to brake the stone and labour to pour the grout. The cost can further be reduced.

IN THIS TECHNOLOGY THE 40MM STONE ACT AS  SOLD PLASTIC CELL .AND THE GROUT RESTRICTS THE BOUNDRIES.
WE CAN SAVE THE ADDITIONAL COST OF PLASTIC CELL.

Conclusion
1)      Affordable technologies are readily available  to use
2)      The citizen of India should examine these technologies

1 comment:

  1. Dust Controlling Binding Compounds as Stadiums, Airports runways, Auto & Rail Roads, Water Canals and Ponds, The fields, Offshore, Sinkholes, Foundations etc.Stabilizes the flowing of Soggy Soils

    Dear Colleagues,

    We’re representatives of Kalmatron® Corporation manufacturer of Concrete Class Upgrading Admixtures, Remedial Coats, and Concrete Regenerative Sprays.

    Restoration of damped and soggy areas up to the finished objects such as stadiums, airports runways, auto & rail roads, water canals and ponds, Cement Plants, Thermal power plants, Fertilizers plants, Steel plants Sulfur producer and Ports Jetty such as Hydro Carbon Surfactant, Hydro Carbon Surface Treatment Material, etc.

    BENEFITS
    · Initial Solubility of KF-D with water 100%
    · The final product of hardening is insoluble even by acid or water containing salts.
    · Complete Reducing of Blaining of standard mix
    · The time of hardening is adjustable by different consumption of KF-D.
    · KF-D has no influence on environment.
    · The applications of KF-D by injection or sorption treatment created a chemically changed structure with increased density and reduction of hydraulic conductivity or Coefficient of Permeability.
    * The costs of the products are easily set-off against the savings made in water, diesel, man-power, servicing intervals and road maintenance, leaving an overall saving to the client.

    Are any other Airports, Federal Highway, Stadiums etc.. using a newer product
    http://www.kalmatron.com/files/Files1/KF-D/AD_of_KF-D.pdf

    The application of KF-D and EMS treatment creates a chemically changed structure of soil and building materials liner with a reduction in hydraulic conductivity. The degree of improvement depends on initial density of the structure. For crumbling soil it is almost 100 times more effective than for untreated soil in stopping of leaks and moisture flow or seeping.

    KALMATRON® KF-D designed as an admixture to the Cement’s Soils Containing Sealers of the CMS (Crumbled Material’s Sealant) for enhancement of soils consolidation with strength accelerating and any required level of liquid impermeability.

    KF-D performs as a compactor of crumbled concrete and densifier of disintegrated and/or soggy soils.

    KF-D provides stable consolidation of injected structures with increasing of compressive strength up to 40%.

    KF-D improves liquid impermeability of Earth-Material’s Structures (EMS) and concrete/masonry building’s elements.

    KF-D stabilizes the flowing of soggy soils of the fields, offshore, sinkholes, foundations, and etc.

    KF-D is a cost‐effective solution that utilizes unusable structures to be restored up to impermeable to the liquids without the need of isolating membranes or water mitigating solutions and devices.

     No Drying Shrinkage and post hardening deformations;
     Exothermic heat is lower by 50%;
     100% water impermeability of EMS and EBS at 3½” to 5” thick layer;
     Strong adhesion to any porous material;
     Increased pumpability;
     Increased workability;
     Eliminates palpability;
     No shrinkage cracks;
     No cracks, flakes, efflorescence and slid areas;
     No bleeding or oozing;
     Highest resistance to climate corrosions;
     Highest freeze-thaw resistance;
     No curing is required.

    It is correct about high probability of rock fill particles rearrangement, but unfortunately there is no universal recipe because every time situation is different. Very often ground stabilization solves the problem by soil premix with additive and placement rock fill after
    http://www.kalmatron.com/5-KF-D.html

    For areas with active filtration or high water table, KF-D must be injected.

    We have favorable prices with free ocean freight and discounts. Sampling is available also.

    With Best Regards,
    Mr. Dilip Shah
    NRD Industries
    USA
    E-mail : nrdindustries@gmail.com,
    Skype ID: dilipshah26
    Dr. Alex Rusinoff
    Visit us at:
    www.drivewayoverlay.com NEW!
    www.kalmatron.com

    ReplyDelete